Aurora Insulation › Blown-In Insulation
Blown-In Insulation in Aurora, CO
In Aurora, Original Aurora bungalows, Del Mar ranches, Southshore and Saddle Rock builds, compacted attic insulation lets the top floor bake. Blown-in restores even, full-depth R-value.
- Free attic depth inspection
- Itemized quote, no pressure
- Xcel rebate guidance
Your Front Range crew
Based in Commerce City, serving Aurora and the metro
Where does your attic actually stand?
R-value in an Aurora attic comes from consistent depth across every square foot, not just what’s piled in the middle, a 6-inch dip near a soffit or a wind-packed corner drags the whole attic’s performance down. Zone 5B calls for R-49 to R-60 up top, and settled or patchy loose-fill in older Aurora attics rarely gets there without a top-off.
- Measured during free inspections across Aurora housing stock. Your exact number comes with your assessment.
TRUSTED PRODUCTS & PARTNERS
The Brands Behind Every Grizzly Install
There’s no mystery bag of insulation going into your attic, every Aurora job uses borate-treated cellulose or certified fiberglass loose-fill from established manufacturers, the same materials used across the Front Range.
01THE PROBLEM
The Attic Problems Blown-In Insulation Quietly Solves.
Original Aurora’s older bungalows often have attics that were insulated decades ago and never topped off, while newer Southshore and Saddle Rock homes can still have builder-grade coverage that’s thinner than it looks. Add Aurora’s wind and hail exposure, and any gap around a can light, chimney chase, or attic hatch turns into a steady heat leak. Homeowners usually blame the furnace or AC, but in most cases it’s under-depth, settled, or wind-disturbed loose-fill and unsealed air leaks doing the damage. The equipment is working fine, the attic just isn’t holding up its end.
A · Attics still sitting at an old R-19 to R-30
Bonus rooms and home offices framed above an attached garage sit over unconditioned space, so heat drains through the floor while the garage pulls it away below. You get cold floors, a room running 10–15° off the rest of the house, and a furnace that never catches up. We insulate the floor joists, knee walls, and sloped ceilings, then air-seal the garage ceiling and rim.
B · Loose-fill that has settled, thinned, or gone flat
Most Aurora basements, the brick ranches east of Wadsworth, the split-levels around Lake Arbor, have bare concrete or block foundation walls. Finishing that basement without insulating the walls first buys you a cold, clammy room and a heating bill to match. Blown-Ins in the new stud walls, with the correct vapor retarder, turn it into comfortable, usable square footage.
C · Bare patches, gaps, and wind-washed eaves
Additions, pop-tops, and finished attic conversions are often framed to the minimum of their day, or never insulated in the walls at all. That leaves one part of the house always chasing the thermostat. Filling the wall, floor, and rafter cavities with properly sized blown-in insulation brings the new space up to the same comfort as the original home.
D · Ice dams and a top floor that never holds heat
Insulation isn’t only about temperature. Blown-Ins packed into interior walls and between floors cut the sound that travels between a media room and the bedrooms, an office and the living room, or upstairs and down. Mineral wool does this best. It’s a small add during a remodel that quietly changes how the whole house feels.
02THE FIX
Cellulose or Fiberglass. One Honest Recommendation.
We start by getting into the attic and measuring actual depth and coverage, not guessing from the hatch. Any air leaks get sealed and eave baffles go in first so airflow from the soffits keeps working, then we recommend cellulose for its dense coverage and borate protection or fiberglass where moisture is a bigger concern, one honest call based on what your attic needs, not a default answer.
03WHAT TO EXPECT
A Half-Day Inside. Here's How It Goes.
A typical Aurora blown-in attic job starts with the inspection and air-sealing, moves into the blow, and wraps with a depth-check across the whole attic, most homes are done in a few hours, start to finish.
We confirm the plan from your assessment, then protect floors and finishes around the work area.
We air-seal top plates, can lights, and the attic hatch, then set baffles at the eaves so airflow cannot wind-wash the new insulation.
Loose-fill is machine-blown evenly across the attic floor to the marked depth, filling every gap around joists, ducts, and penetrations.
We check coverage against depth-ruler cards staked across the attic so you hit the rated R-value corner to corner.
We vacuum up, haul away offcuts, and walk every cavity with you before we leave.
The Grizzly 100% Guarantee
If the work isn't right, we make it right. That's the reputation we've built across the Front Range, and it's our only sales pitch.
04COST & SAVINGS
What Blown-In Insulation Costs in Aurora
No two Aurora attics price the same. What moves the number is attic square footage, how much depth you need to hit your target R-value, how much air-sealing the attic needs, and whether old, soiled, or hail-compressed insulation has to come out before we blow in new material. You’ll get an itemized quote before we start, not a flat number pulled out of thin air.
Attic square footage
The attic floor area we cover to target depth
Current attic R-value
How far your attic sits below the Zone 5B target
Air-sealing & baffles
Top plates, can lights, hatch, and eave baffles
Removal needs
Only if material is soiled or damaged
Three ways the net cost drops
Xcel Energy rebates
Qualifying insulation + air-sealing upgrades earn utility rebates across Aurora. We flag what applies in your estimate.
Federal 25C tax credit
30% of qualifying insulation costs, up to $1,200 per year, under the Inflation Reduction Act.
Lower bills, every month
Heating and cooling dominate Front Range energy bills, and unconditioned walls and floors are among the highest-impact upgrade point in most Aurora homes.
★ ★ ★ ★ ★
Our upstairs bedrooms in Southshore used to feel like an oven by 4pm every summer afternoon, and last winter we had ice dams along the whole north side of the roof. Grizzly topped off our attic and sealed the gaps around the can lights, and this summer the upstairs actually stays comfortable without cranking the AC. Our January gas bill was noticeably lower too.
D
David R.
05QUESTIONS
Blown-In Insulation in Aurora, Answered Straight
Prefer to just ask?
Call the crew that’s actually going to be in your attic, (303) 854-6221, for a free, no-pressure assessment of what your Aurora home needs.
Blown-in insulation is loose-fill cellulose or fiberglass that’s machine-blown into the attic to a measured, even depth rather than installed as cut panels. In Aurora it’s used almost exclusively on attic floors, over open joists, around obstructions, and into corners batts can’t fully fill. It’s also used to top off older insulation that’s settled or thinned out over the years.
Both perform well when installed to full depth; the right choice depends on your attic. Cellulose packs densely and is borate-treated, which many Original Aurora homeowners like for its coverage in older, irregular attic framing. Fiberglass won’t settle over time and handles minor moisture better, which can matter in attics with bath fan venting nearby. We’ll recommend one based on what we find during the inspection, not a standard answer.
Yes, in most Aurora attics we blow new insulation directly over existing material rather than removing it, as long as what’s there is dry and in reasonable shape. If old insulation is soiled, compressed by hail-damaged roof repairs, or you’ve had a leak, we’ll remove that portion first. Either way, we measure existing depth before adding to it so you land at your target R-value.
Climate Zone 5B, which covers Aurora, calls for an attic R-value of R-49 to R-60, which generally translates to about 14 to 17 inches of cellulose or 16 to 20 inches of fiberglass depending on the product’s coverage chart. We measure to actual depth across the attic, not just at the hatch, since coverage varies a lot in older Aurora homes.
Cellulose settles somewhat after installation, which is why we install it to account for that settling and hit your target depth long-term. Loose-fill of either type can also get pushed around by attic bypass air leaks or wind-washing near soffits, which is why air-sealing and eave baffles matter as much as the insulation itself. A thin or patchy attic after several years is usually a sign it’s time for a top-off, not a defect in the material.
Blown-in wins in attics with irregular framing, existing insulation to top off, or lots of obstructions like ductwork and wiring, which describes most Aurora attics. Batts make more sense in open wall cavities where a consistent cavity depth exists. Spray foam has its place for complex rooflines or conditioned attics, but it costs more and isn’t necessary for a standard vented attic floor, for most Aurora homes, blown-in gets you to code-level R-value for less.
06EVERY COMMUNITY WE SERVE
Blown-In Insulation Near Aurora
AuroraBoulderBrightonBroomfieldCentennialColorado SpringsCommerce CityDenverFort CollinsGreeleyHighlands RanchLakewoodLittletonLongmontLovelandParkerThorntonWestminster
07GET STARTED
Find Out How Much Heat Your Attic Is Losing.
We back every job with a 100% guarantee, so there’s no risk in finding out.
- (303) 854-6221 · Mon–Sat 8 AM–5 PM · Sun by appointment
- info@grizzlyinsulationco.com, fast replies, usually same day
- 7140 Ivy St Unit B, Commerce City, CO 80022, 10 miles from Aurora
Get Your Free Blown-In Quote
Takes 30 seconds. We reply within 24 hours.